INF-8077i XFP register map

Đội ngũ của chúng tôi đang thực hiện bản dịch. Bài viết này tạm thời chưa có bản tiếng Việt và đang được hiển thị bằng tiếng Anh.

An XFP module answers at one two-wire address (A0h) with a lower memory of 128 bytes — thresholds, flags, monitors and control — and upper tables selected by byte 127, of which table 01h is the serial ID. The layout predates SFF-8636 and was its model: the QSFP identity block copies XFP's byte positions almost exactly. This page lists the lower memory and table 01h byte by byte and bit by bit, compiled against INF-8077i Rev 4.5. Narrative: INF-8077i — XFP management.

Legend: rsvd = reserved · vendor = vendor specific · 16-bit values are MSB first · flags are latched, cleared on read.

Lower memory — thresholds, bytes 0–57

Byte	Field	Notes
0	Identifier	06h = XFP
1	Signal conditioner control	7 Tx CDR bypass? — bits control internal Tx/Rx CDR and loopbacks per Table 39: 7 Tx CDR off · 6 Tx amplitude/EQ control · 5–4 rsvd · 3 Rx CDR off · 2 line-side loopback · 1 XFI loopback · 0 rsvd (implementation advertised in table 01h byte 164)
2–3 / 4–5 / 6–7 / 8–9	Temperature high alarm / low alarm / high warning / low warning	signed 16-bit, 1/256 °C
10–17	rsvd	(thresholds for a second temperature in some drafts)
18–19 / 20–21 / 22–23 / 24–25	Tx bias HA / LA / HW / LW	unsigned 16-bit, 2 µA
26–27 / 28–29 / 30–31 / 32–33	Tx power HA / LA / HW / LW	unsigned 16-bit, 0.1 µW
34–35 / 36–37 / 38–39 / 40–41	Rx power HA / LA / HW / LW	unsigned 16-bit, 0.1 µW
42–43 / 44–45 / 46–47 / 48–49	AUX1 HA / LA / HW / LW	format per AUX1 type (table 01h byte 222)
50–57	AUX2 HA / LA / HW / LW	as AUX2 type

Lower memory — vendor, BER and wavelength control, bytes 58–79

Byte	Field	Contents
58–69	vendor	—
70	BER reporting	for modules with FEC: BER exponent/mantissa reporting control
71	Wavelength control — target MSB	tunable XFP: 71–72 wavelength set in 0.05 nm units
72	Wavelength control — target LSB	—
73–74	Wavelength error / status	reported wavelength offset in 0.005 nm units
75	Wavelength control flags	tuning in progress, unlocked, out of range
76–79	FEC control	enable/disable FEC, FEC status (10G FEC XFPs, ITU G.709 wrapped)

Lower memory — flags, bytes 80–95

Byte	Field	Bits
80	Alarm flags 1 (latched)	7 temp high alarm · 6 temp low alarm · 5 rsvd · 4 rsvd · 3 Tx bias high alarm · 2 Tx bias low alarm · 1 Tx power high alarm · 0 Tx power low alarm
81	Alarm flags 2 (latched)	7 Rx power high alarm · 6 Rx power low alarm · 5 AUX1 high alarm · 4 AUX1 low alarm · 3 AUX2 high alarm · 2 AUX2 low alarm · 1–0 rsvd
82	Warning flags 1 (latched)	same layout as byte 80 for warnings
83	Warning flags 2 (latched)	same layout as byte 81 for warnings
84	Status flags 1 (latched)	7 Tx_NR (not ready) · 6 Tx_Fault · 5 Tx CDR not locked · 4 Rx_NR · 3 Rx CDR not locked · 2 RX_LOS · 1 module not ready (Mod_NR) · 0 reset complete
85	Status flags 2 (latched)	7 APD supply fault · 6 TEC fault · 5 wavelength unlocked · 4–3 rsvd · 2 VCC5 fault? · 1 VCC3 fault · 0 VCC2 fault (supply-fault bits per implementation)
86–87	rsvd	—
88	Alarm masks 1	mask bits for byte 80
89	Alarm masks 2	for byte 81
90	Warning masks 1	for byte 82
91	Warning masks 2	for byte 83
92	Status masks 1	for byte 84
93	Status masks 2	for byte 85
94–95	rsvd	—

A set flag asserts the Interrupt pin unless masked; the host reads the flag bytes to clear them.

Lower memory — A/D readouts, bytes 96–109

Bytes	Monitor	Format
96–97	Temperature	signed 16-bit, 1/256 °C
98–99	rsvd	—
100–101	Tx bias	2 µA
102–103	Tx power	0.1 µW
104–105	Rx power	0.1 µW
106–107	AUX1	per type in table 01h byte 222
108–109	AUX2	per type

Lower memory — control and status, bytes 110–127

Byte	Field	Bits
110	General control/status	7 TX_DIS pin state · 6 soft TX_DIS (R/W) · 5 MOD_NR state · 4 P_Down state (pin) · 3 soft P_Down (R/W) · 2 Interrupt state · 1 RX_LOS state · 0 data not ready
111	General status 2	7 Tx_NR state · 6 Tx_Fault state · 5 Tx CDR not locked · 4 Rx_NR state · 3 Rx CDR not locked · 2 rsvd · 1 VPS (variable power supply) state · 0 rsvd (unlatched mirrors of byte 84)
112–117	vendor / rsvd	—
118	vendor	—
119–122	vendor	often password change area
123–126	vendor	often password entry area (same offsets as QSFP) — Write-protection types
127	Table select	01h serial ID (default) · 02h–7Fh rsvd · 80h–FFh vendor

Table 01h — serial ID, bytes 128–191 (covered by CC_BASE)

Byte	Field	Contents
128	Identifier	06h XFP
129	Extended identifier	7–6 rsvd · 5–4 power level: 00 ≤ 1.5 W · 01 ≤ 2.5 W · 10 ≤ 3.5 W · 11 > 3.5 W · 3 CDR (0 = XFI with CDR, 1 = no CDR) · 2 CLEI code present in table 01h? (bit 2 = CLEI in table 02h) · 1 Tx reference clock input required · 0 rsvd
130	Connector	SFF-8024 Table 4-3 (07h LC · 01h SC · 21h copper pigtail · 22h RJ45)
131	10G Ethernet compliance	7 10GBASE-SR · 6 10GBASE-LR · 5 10GBASE-ER · 4 10GBASE-LRM · 3 10GBASE-SW · 2 10GBASE-LW · 1 10GBASE-EW · 0 rsvd
132	10G Fibre Channel compliance	7 1200-MX-SN-I · 6 1200-SM-LL-L · 5 extended reach 1550 nm · 4 intermediate reach 1300 nm FP · 3–0 rsvd
133	10G copper links	7–0 rsvd (defined for future copper XFP)
134	Lower-speed links	7 1000BASE-SX / 1×FC MMF · 6 1000BASE-LX / 1×FC SMF · 5 2×FC MMF · 4 2×FC SMF · 3 OC-48 SR · 2 OC-48 IR · 1 OC-48 LR · 0 rsvd
135	SONET/SDH interconnect	7 I-64.1r · 6 I-64.1 · 5 I-64.2r · 4 I-64.2 · 3 I-64.3 · 2 I-64.5 · 1–0 rsvd
136	SONET/SDH short haul	7 S-64.1 · 6 S-64.2a · 5 S-64.2b · 4 S-64.3a · 3 S-64.3b · 2 S-64.5a · 1 S-64.5b · 0 rsvd
137	SONET/SDH long haul	7 L-64.1 · 6 L-64.2a · 5 L-64.2b · 4 L-64.2c · 3 L-64.3 · 2 G.959.1 P1L1-2D2 · 1–0 rsvd
138	SONET/SDH very long haul	7 V-64.2a · 6 V-64.2b · 5 V-64.3 · 4–0 rsvd
139	Encoding	7 64B/66B · 6 8B/10B · 5 SONET scrambled · 4 NRZ · 3 RZ · 2–0 rsvd (bit field, not an SFF-8024 value)
140	Bit rate minimum	units of 100 Mb/s (e.g. 5Fh = 9.5 Gb/s)
141	Bit rate maximum	units of 100 Mb/s (e.g. 6Fh = 11.1 Gb/s) — the pair defines the supported rate window
142	Length SMF	km
143	Length E-50 µm (OM3)	units of 2 m
144	Length 50 µm	units of 1 m
145	Length 62.5 µm	units of 1 m
146	Length copper	units of 1 m
147	Device technology	7–4 transmitter: 0h 850 nm VCSEL · 1h 1310 nm VCSEL · 2h 1550 nm VCSEL · 3h 1310 nm FP · 4h 1310 nm DFB · 5h 1550 nm DFB · 6h 1310 nm EML · 7h 1550 nm EML · 8h copper · 9h–Fh rsvd · 3 wavelength control (active) · 2 cooled transmitter · 1 detector (1 = APD, 0 = PIN) · 0 tunable
148–163	Vendor name	16 ASCII
164	CDR support	7 9.95 Gb/s · 6 10.3 Gb/s · 5 10.5 Gb/s · 4 10.7 Gb/s · 3 11.1 Gb/s · 2 rsvd · 1 line-side loopback supported · 0 XFI loopback supported
165–167	Vendor OUI	—
168–183	Vendor PN	16 ASCII
184–185	Vendor rev	2 ASCII
186–187	Wavelength	units of 0.05 nm (1310.00 nm = 26 200 = 6658h)
188–189	Wavelength tolerance	units of 0.005 nm
190	Max case temperature	°C
191	CC_BASE	(Σ bytes 128–190) mod 256

Table 01h — extended ID, bytes 192–255

Byte	Field	Contents
192	Max power dissipation	units of 20 mW (e.g. 7Dh = 2.5 W)
193	Total power in power-down	units of 20 mW
194	Max current	7–4 on +5 V in 50 mA units · 3–0 on +3.3 V in 100 mA units
195	Max current	7–4 on +1.8 V in 100 mA units · 3–0 on −5.2 V in 50 mA units
196–211	Vendor SN	16 ASCII
212–219	Date code	`YYMMDD` + 2 lot
220	Diagnostic monitoring type	7–5 rsvd · 4 Rx power measurement: 1 = average, 0 = OMA · 3 BER reporting supported · 2–0 rsvd
221	Enhanced options	7 VPS supported (variable power supply) · 6 soft TX_DISABLE implemented · 5 soft P_Down implemented · 4 VPS LV regulator mode · 3 VPS bypassed regulator mode · 2 active FEC control functions · 1 wavelength tunability implemented · 0 CMU (clock multiplier unit) supported
222	AUX monitoring	7–4 AUX1 type · 3–0 AUX2 type: 0 not implemented · 1 APD bias voltage (10 mV) · 2 rsvd · 3 TEC current (0.1 mA, signed) · 4 laser temperature (1/256 °C) · 5 laser wavelength (0.05 nm? — per spec: wavelength offset) · 6 +5 V supply (100 µV) · 7 +3.3 V supply · 8 +1.8 V supply · 9 −5.2 V supply · Ah +5 V current (100 µA) · Bh rsvd · Ch +3.3 V current · Dh +1.8 V current · Eh −5.2 V current · Fh rsvd
223	CC_EXT	(Σ bytes 192–222) mod 256
224–255	Vendor specific	not checksummed

Tables 02h–FFh

Table	Contents
02h	user EEPROM / CLEI code (when advertised)
03h–7Fh	rsvd
80h–FFh	vendor specific (often passwords, calibration backups)

What the QSFP inherited

Compare with the SFF-8636 upper page 00h map: bytes 128–130, 140–147 (lengths and technology nibble), 148–191 (vendor block, wavelength, CC_BASE), 196–223 (SN, date, CC_EXT) sit at the same offsets. The differences are the compliance bytes (131–138 redefined for 40/100G Ethernet), byte 139 (encoding as a value rather than a bit field) and 192–195 (power/current replaced by extended compliance and options). A tool that knows one map reads the other with a small translation table.

INF-8077i narrative — practical differences and X2/XENPAK.
SFF-8472 A2h map — the SFP diagnostics device for comparison.
Memory map quick reference.

Nếu bạn phát hiện thông tin chưa chính xác hoặc lỗi trong bài viết này, hãy chọn đoạn liên quan và nhấn Ctrl+Enter để .